Jan 15, 2020 · Last configuration change at 11:27:41 UTC Fri Jun 2 2017 upgrade fpd auto version 15.2 service timestamps debug datetime msec service timestamps log datetime msec no service password-encryption ! hostname R1 ! boot-start-marker boot-end-marker ! ! no aaa new-model no ip icmp rate-limit unreachable ! ! no ip domain lookup ip cef no ipv6 cef
multilink bundle-name authenticated! interface Loopback0. ip address 209.165.200.225 255.255.255.0! interface Embedded-Service-Engine0 / 0. no ip address. shutdown! multilink bundle-name authenticated! interface Loopback0. ip address 198.133.219.1 255.255.255. 255! interface Embedded-Service-Engine0 / 0. no ip address. shutdown! Mar 08, 2012 · Cisco IOS software builds a multilink bundle name based on the PPP authenticated name first, then based on the endpoint discriminator. With Cisco IOS in its default state, all client links that use the same username are bundled together into the same MP virtual connection. Mar 13, 2020 · multilink bundle-name authenticated! interface Loopback0. ip address 192.31.7.1 255.255.255.255! interface Embedded-Service-Engine0 / 0. no ip address. shutdown! Mar 06, 2020 · CCNA RSE Lab: 3.2.1.9 Configuring Basic RIPv2 CCNA 2 Lab 3.2.1.9 lab – configuring basic ripv2 packet tracer Answers Topology Addressing Table Objectives Part 1: Build the Network and Configure Basic Device Settings Part 2: Configure and Verify RIPv2 Routing Configure RIPv2 on the routers and verify that it is running. Configure a passive interface. […] Jan 15, 2020 · Last configuration change at 11:27:41 UTC Fri Jun 2 2017 upgrade fpd auto version 15.2 service timestamps debug datetime msec service timestamps log datetime msec no service password-encryption ! hostname R1 ! boot-start-marker boot-end-marker ! ! no aaa new-model no ip icmp rate-limit unreachable ! ! no ip domain lookup ip cef no ipv6 cef Jun 21, 2018 · Create the crypto map on R1, name it CMAP, and use 10 as the sequence number. A message displays after the command is issued. A message displays after the command is issued. R1(config)# crypto map CMAP 10 ipsec-isakmp % NOTE: This new crypto map will remain disabled until a peer and a valid access list have been configured.
No inactive multilink interfaces. Note the Bundle name: line at the beginning of the output. Because the bundle naming is now configured to authenticated, the remote username is used to identify the bundle. After changing the multilink bundle-name to endpoint and resetting the PPP session, show ppp multilink on R2 shows:
Current configuration : 1130 bytes ! version 12.4 service timestamps debug datetime msec service timestamps log datetime msec no service password-encryption ! hostname R2 ! boot-start-marker boot-end-marker ! no aaa new-model memory-size iomem 5 no ip icmp rate-limit unreachable ip cef ! no ip domain lookup ! multilink bundle-name authenticated no ip bootp server ip domain name internode.on.net ip name-server 192.231.203.132 ip name-server 192.231.203.3 ! multilink bundle-name authenticated ! ! username Jan 16, 2020 · ip name-server 8.8.8.8 ip cef no ipv6 cef multilink bundle-name authenticated!!! license udi pid xxxxxxxxxxxxxxxxxxxxxx!!! redundancy!!!!! interface Embedded-Service-Engine0/0 no ip address shutdown! interface GigabitEthernet0/0 description to the ISP ip address xxxx xxxx ip nat outside ip virtual-reassembly in duplex auto speed auto! multilink bundle-name authenticated ! archive log config hidekeys ! interface Loopback0 ip address 172.16.2.1 255.255.255.224 ! interface Loopback1 ip address 172.16
multilink bundle-name authenticated ! ! ! ! ip tcp synwait-time 5 ! ! ! ! ! interface Loopback0 ip address 1.1.1.1 255.255.255.255 ! interface Tunnel0 ip vrf
Aug 28, 2012 · ip domain name yourdomain.com no ipv6 cef multilink bundle-name authenticated license udi pid CISCO891-K9 sn FCZ16xxxxxxx username tssuser password 0 1xxxxxxx interface FastEthernet0 interface FastEthernet1 interface FastEthernet2 interface FastEthernet3 interface FastEthernet4 interface FastEthernet5 interface FastEthernet6 interface FastEthernet7 Oct 15, 2008 · join the interfaces into the one multilink bundle because the mppp bundle-name discriminator is the same. I have tried influencing the discriminator at both ends but it always uses the SGBP group name on the customers router. We don't want both interfaces in the same bundle for various reasons but we do require mppp on both links. ip dhcp pool guest import all network 192.168.3.0 255.255.255.0 default-router 192.168.3.1 dns-server 10.171.12.5 10.171.12.37 ! ip cef no ip domain lookup no ipv6 cef ! multilink bundle-name authenticated license udi pid CISCO891W-AGN-A-K9 sn FTX153085WL ! ip domain name test.lan ip name-server YOUR_DNS_IP ip multicast-routing no ipv6 cef! multilink bundle-name authenticated!!!!! voice service voip ip address trusted list ipv4 65.254.44.194 ipv4 74.81.71.18 ipv4 10.1.10.11 allow-connections h323 to h323 allow-connections h323 to sip allow-connections sip to h323 allow-connections sip to sip multilink bundle-name authenticated!!!!! license udi pid CISCO891-K9 sn FCZ1747C1E8!! username vsz privilege 15 password 0 xxxxxx! redundancy!!!!! interface FastEthernet0 no ip address! interface FastEthernet1 no ip address! interface FastEthernet2 no ip address! interface FastEthernet3 no ip address! interface FastEthernet4 no ip address! Jun 21, 2018 · ContentsLab – Securing Layer 2 Switches (Instructor Version)TopologyIP Addressing TableObjectivesBackground / ScenarioRequired ResourcesPart 1: Configure Basic Switch SettingsStep 1: Cable the network as shown in the topology.Step 2: Configure basic settings for the router and each switch.Step 3: Configure PC host IP settings.Step 4: Verify basic network connectivity.Step 5: Save the basic